廣東>深圳市水天藍環保科技有限公司反滲透膜樹脂>供求信息

現貨供應羅門哈斯電站凝結水精處理樹脂AMBERLITE IRN160 

現貨供應羅門哈斯電站凝結水精處理樹脂AMBERLITE IRN160

   聯系電話：高經理135 2872 1531  QQ:32515 89577

    羅門哈斯AMBERLITE IRN160是均粒、凝膠型強酸陽離子交換樹脂和強堿陰離子交換樹脂的混合物。其出廠形態為H﹢/OH-型，且達到了動態平衡轉型極限。AMBERLITE IRN160適用于核廢水處理和沸水堆核電站凝結水精處理深層混床處理。該樹脂具有較高交換容量和優異的抗磨檫和滲透壓力能力的特點。陰樹脂和陽樹脂不分離的特性使該混合樹脂輸送非常簡單，不會產生陰陽樹脂分離的現象。  

羅門哈斯AMBERLITE IRN160是通過特殊工藝制造的，專為核電站水質工程設計的核級混合樹脂。這種特殊的樹脂制造工藝再結合羅門哈斯公司降低陰離子交換樹脂中氯型樹脂含量的后處理工藝，使樹脂達到一種極限純度，以滿足核工業的嚴格要求。應用及建議運行條件

羅門哈斯AMBERLITE IRN160具有極高的純度和優良的物理穩定性，在核電站的使用中表現出了其它樹脂不可替代的優越性。陰陽樹脂不分離的特性使其成為以下幾個應用領域的最佳選擇。 ·沸水堆核電站凝結水精處理深層混床 ·核廢水除鹽 ·混床除鹽 AMBERLITE IRN160同樣可以應用于各種不同的核廢水處理。

最小床深------------------------------------------------800mm

最高使用溫度--------------------------------------------60℃

運行流量------------------------------------------------80BV/h

運行流速------------------------------------------------120m/h(35-50℃)

BASIC RESIN PROPERTIES
In non-regenerable final polishing applications,
UPW performance is much more significant than
basic resin properties. It is still important to
know that the resins used in the application are
of the highest capacity and total quality. The
typical properties of the resins used in Amberjet
UP6040 are shown below. These values are listed
to show that both the cation and anion resins
used to make Amberjet UP6040 meet stringent
standards for high capacity, uniform particle size
ion exchange resins.
Cation H+ Anion OH 
–
Moisture holding capacity, % _________________ 44.0 - 51.0 54.0 - 60.0
Total exchange capacity, eq/L ________________ ≥ 2.00 ≥ 1.10
Uniformity coefficient _______________________ ≤ 1.20 ≤ 1.20
H form % of sites ________________________ ≥ 99 -
OH form % of sites ________________________ - ≥ 95.0
Cl form, % of sites ________________________ - ≤ 0.5
CO3 form % of sites ________________________ - ≤ 5.0
SO4 form % of sites ________________________ - ≤ 0.1

Feed water temperature______________________ 15 to 25°C (60 to 77° F)
Minimum bed depth ________________________ 900 mm (3 feet)
Service flow rate ____________________________ 30 to 50 BV*/h
Recommended influent water quality
Inlet Resistivity ____________________________ > 17 MΩ·cm
Inlet Silica ________________________________ < 2 ppb
Inlet Total Organic Carbon _________________ < 15 ppb